Availability: | |
---|---|
Quantity: | |
MS10
Howell
HM-MS10
Fixall High Performance MS Hybrid Sealant
MS10 is a silane-modified polyether sealant (MS sealant), which is a moisture-curable elastic sealant,elastic structural adhesive, and sealing coating. The moisture mainly comes from the air. MS10 not onlyhas excellent environmental performance, but also has excellent bonding to different substrates.Compared with traditional sealants and adhesives such as silicone and polyurethane, it has manyexcellent properties such as solvent-free, low VOC, no free isocyanate, surface paintable, and nobubbles in the curing process. It is especially suitable for construction, industry, transportation, and newenergy. and other fields.
High-grade aluminum profile door and window sealing
Marble curtain wall bonding and caulking
Aluminum plastic panel curtain wall bonding and caulking
Building interior decoration
Bonding and sealing of automobiles, ships, elevators, cold storage, etc.
Code# | MS10 |
Shelf Life | 12months |
Properties Uncured | |
Skin forming time (min)23 °C | 50 % r.h | 20 |
Density (g/cm3) | 1.52 |
Consistency | non-sag |
Properties Cured | |
Hardness (Shore A) | 44 |
Elongation at break (%) | 350 |
Tensile strength (N/mm2) | 2.0 |
Sealant grade | 20HM |
The above data is tested at 25℃ and 50% relative humidity. After cured for 21 days at a humidity of 50±5% and a temperature of 23±2℃ Standard colors are white, black, gray, and transparent. Other colors can be provided according to customer needs. |
Construction:
Cut the branch opening, put on the glue nozzle, cut the glue nozzle into a suitable slope, and apply it tothe construction site with a glue extrusion gun. During pneumatic gluing, the air pressure isrecommended not to exceed 0.4 MPa, and the construction temperature is recommended to be 4°C -40°C
Curing:
Place the glued parts in the air. After the skin is formed, it will cure from the surface to the inside. Thecuring depth will be 2~4mm within 24 hours at room temperature and 55% relative humidity. As timegoes by, the curing depth gradually increases.
Storage:
Unused glue should be tightened immediately and the nozzle should be sealed for storage. When usingit again, if there is a little crust on the seal, just remove it and it will not affect normal use. During thestorage process, a small amount of crusting may also appear on the branch mouth. After removal, it canbe used normally without affecting product performance.
Standard 300ml plastic bottle packing, 24pcs/carton;
500-600ml flexible film packing, 20pcs/carton
Store the original sealant in a dry place, the temperature should not be higher than 27 °C, and the storageperiod is 12 months from the date of production
HM-MS10
Fixall High Performance MS Hybrid Sealant
MS10 is a silane-modified polyether sealant (MS sealant), which is a moisture-curable elastic sealant,elastic structural adhesive, and sealing coating. The moisture mainly comes from the air. MS10 not onlyhas excellent environmental performance, but also has excellent bonding to different substrates.Compared with traditional sealants and adhesives such as silicone and polyurethane, it has manyexcellent properties such as solvent-free, low VOC, no free isocyanate, surface paintable, and nobubbles in the curing process. It is especially suitable for construction, industry, transportation, and newenergy. and other fields.
High-grade aluminum profile door and window sealing
Marble curtain wall bonding and caulking
Aluminum plastic panel curtain wall bonding and caulking
Building interior decoration
Bonding and sealing of automobiles, ships, elevators, cold storage, etc.
Code# | MS10 |
Shelf Life | 12months |
Properties Uncured | |
Skin forming time (min)23 °C | 50 % r.h | 20 |
Density (g/cm3) | 1.52 |
Consistency | non-sag |
Properties Cured | |
Hardness (Shore A) | 44 |
Elongation at break (%) | 350 |
Tensile strength (N/mm2) | 2.0 |
Sealant grade | 20HM |
The above data is tested at 25℃ and 50% relative humidity. After cured for 21 days at a humidity of 50±5% and a temperature of 23±2℃ Standard colors are white, black, gray, and transparent. Other colors can be provided according to customer needs. |
Construction:
Cut the branch opening, put on the glue nozzle, cut the glue nozzle into a suitable slope, and apply it tothe construction site with a glue extrusion gun. During pneumatic gluing, the air pressure isrecommended not to exceed 0.4 MPa, and the construction temperature is recommended to be 4°C -40°C
Curing:
Place the glued parts in the air. After the skin is formed, it will cure from the surface to the inside. Thecuring depth will be 2~4mm within 24 hours at room temperature and 55% relative humidity. As timegoes by, the curing depth gradually increases.
Storage:
Unused glue should be tightened immediately and the nozzle should be sealed for storage. When usingit again, if there is a little crust on the seal, just remove it and it will not affect normal use. During thestorage process, a small amount of crusting may also appear on the branch mouth. After removal, it canbe used normally without affecting product performance.
Standard 300ml plastic bottle packing, 24pcs/carton;
500-600ml flexible film packing, 20pcs/carton
Store the original sealant in a dry place, the temperature should not be higher than 27 °C, and the storageperiod is 12 months from the date of production
Anti-mildew | Aquarium | Automobile | Construction Exterior Wall | Decoration | Electronics | Elevator | Farbricated Building | Home Appliances | Infrastructure | Nail Free | Pipe Thread Locking | Planar Sealing | Rail Traffic | Screw-locking | Silicone Conformal Coatings | Universal | Waterproof | Windows&Sun Romms