 |
| Quantity: | |
|---|---|
MS100
Howell
HM-MS100
General Purpose Translucent MS Hybrid Sealant
General-purpose translucent MS100 Sealant is an environment-friendly, low VOC adhesive and sealant. This translucent MS polymer formula provides strong bonding, flexibility, and durability,making it ideal for a wide range of applications while maintaining a clean, aesthetic finish.
◆Sealing for Aluminum Profiles in Doors and Windows
◆Bonding and Sealing for Marble Curtain Walls
◆Bonding and Sealing for Aluminum Composite Panels
◆Interior Decoration Sealing and Bonding
◆Sealing and Bonding for Automobiles, Ships, Elevators, and Cold Storage
| Code# | MS100 |
| Shelf Life | 12months |
| Properties Uncured | |
Skin forming time (min)23 °C | 50 % r.h | 20 |
| Density (g/cm3) | 1.02 |
| Consistency | non-sag |
| Properties Cured | |
Hardness (Shore A) | 28 |
Elongation at break (%) | 380 |
Tensile strength (N/mm2) | 1.40 |
| Sealant grade | 20HM |
The above data is tested at 25℃ and 50% relative humidity. After cured for 21 days at a humidity of 50±5% and a temperature of 23±2℃ Standard colors are white, black, gray, and transparent. Other colors can be provided according to customer needs. | |
Construction:
Cut the branch opening, put on the glue nozzle, cut the glue nozzle into a suitable slope, and apply it tothe construction site with a glue extrusion gun. During pneumatic gluing, the air pressure isrecommended not to exceed 0.4 MPa, and the construction temperature is recommended to be 4°C -40°C
Curing:
Place the glued parts in the air. After the skin is formed, it will cure from the surface to the inside. Thecuring depth will be 2~4mm within 24 hours at room temperature and 55% relative humidity. As timegoes by, the curing depth gradually increases.
Storage:
Unused glue should be tightened immediately and the nozzle should be sealed for storage. When usingit again, if there is a little crust on the seal, just remove it and it will not affect normal use. During thestorage process, a small amount of crusting may also appear on the branch mouth. After removal, it canbe used normally without affecting product performance.
Standard 300ml plastic bottle packing, 24pcs/carton;
500-600ml flexible film packing, 20pcs/carton
Store the original sealant in a dry place, the temperature should not be higher than 27 °C, and the storageperiod is 12 months from the date of production
HM-MS100
General Purpose Translucent MS Hybrid Sealant
General-purpose translucent MS100 Sealant is an environment-friendly, low VOC adhesive and sealant. This translucent MS polymer formula provides strong bonding, flexibility, and durability,making it ideal for a wide range of applications while maintaining a clean, aesthetic finish.
◆Sealing for Aluminum Profiles in Doors and Windows
◆Bonding and Sealing for Marble Curtain Walls
◆Bonding and Sealing for Aluminum Composite Panels
◆Interior Decoration Sealing and Bonding
◆Sealing and Bonding for Automobiles, Ships, Elevators, and Cold Storage
| Code# | MS100 |
| Shelf Life | 12months |
| Properties Uncured | |
Skin forming time (min)23 °C | 50 % r.h | 20 |
| Density (g/cm3) | 1.02 |
| Consistency | non-sag |
| Properties Cured | |
Hardness (Shore A) | 28 |
Elongation at break (%) | 380 |
Tensile strength (N/mm2) | 1.40 |
| Sealant grade | 20HM |
The above data is tested at 25℃ and 50% relative humidity. After cured for 21 days at a humidity of 50±5% and a temperature of 23±2℃ Standard colors are white, black, gray, and transparent. Other colors can be provided according to customer needs. | |
Construction:
Cut the branch opening, put on the glue nozzle, cut the glue nozzle into a suitable slope, and apply it tothe construction site with a glue extrusion gun. During pneumatic gluing, the air pressure isrecommended not to exceed 0.4 MPa, and the construction temperature is recommended to be 4°C -40°C
Curing:
Place the glued parts in the air. After the skin is formed, it will cure from the surface to the inside. Thecuring depth will be 2~4mm within 24 hours at room temperature and 55% relative humidity. As timegoes by, the curing depth gradually increases.
Storage:
Unused glue should be tightened immediately and the nozzle should be sealed for storage. When usingit again, if there is a little crust on the seal, just remove it and it will not affect normal use. During thestorage process, a small amount of crusting may also appear on the branch mouth. After removal, it canbe used normally without affecting product performance.
Standard 300ml plastic bottle packing, 24pcs/carton;
500-600ml flexible film packing, 20pcs/carton
Store the original sealant in a dry place, the temperature should not be higher than 27 °C, and the storageperiod is 12 months from the date of production
